-
SKU# LED-PS12V-450W-ULImportant Features:- Input: 90 VAC to 132 VAC, 180 VDC to 264 VDC
- Efficiency: 83%
- Protections: Short circuit / Overload / Over voltage/Over temperature
- Ripple and Noise (mV p-p): 200
- Built-in remote sense function
- LED indicator for power on
- Switch-selectable AC input
- Load Regulation: 1.0%
- Line Regulation: 0.5%
- UL Recognized
- Non-Waterproof IP40
- 5 years warranty
- For use in the USA & Europe
- 1 Output
- Input: 90 VAC to 132 VAC, 180 VDC to 264 VDC
- Maximum Output Power: 450 W
- Output Voltage: 12 V
- Output Current: 37.5 A
- Output Connector Type: Screw Terminal Block
- Minimum Isolation Voltage: 3000V
- Size: 8.9"L x 4.9"W x 2.0"H
- Indoor LED lighting
- LED decorative lighting
- LED office lighting
- General electronic products in dusty or humid environments
-
SKU# LED-PS12V-200W-ULImportant Features:- Input: 90-132VAC / 180-264VAC @ 47-63Hz selectable by switch, or 254-370VDC
- Efficiency: 85%
- Protections: Short circuit / Overload / Over voltage/Over temperature
- Cooling by free air convection
- Withstand 300VAC surge input for 5 seconds
- Built-in constant current limiting circuit
- LED indicator for power on
- Fixed switching frequency at 90KHz
- 100% full load burn-in test
- UL Recognized
- Non-Waterproof IP40
- 2 years warranty
- For use in the USA & Europe
- 1 Output
- Input: 90-132VAC / 180-264VAC @ 47-63Hz selectable by switch, or 254-370VDC
- Maximum Output Power: 204 W
- Output Voltage: 12 V
- Output Current: 17 A
- Output Connector Type: Screw Terminal Block
- Minimum Isolation Voltage: 3000V
- Size: 8.5"L x 4.5"W x 2.0"H
- Weight: 2.1 lbs.
- Indoor LED lighting
- LED decorative lighting
- LED office lighting
- General electronic products in dusty or humid environments
-
SKU# IA-HW-001018The MADRIX NEBULA directly connects to your LED pixels. This advanced SPI decoder receives control data over USB or Art-Net over Ethernet network and is built to provide excellent image quality. Features: Direct Connection Directly connect to a wide range of supported LEDs via two 4-pin screw terminals. A signal frequency of up to 24 MHz is available. Supply power over USB or 5 V to 24 V over a 2-pin screw terminal. Quality Output Of 8 Universes Each device drives up to 1.360 RGB pixels while ensuring responsive delivery of high-quality signals to each individual LED. You can choose the output protocol separately for each of the two ports. SPI Converter Art-Net is directly converted to SPI without the need for an additional interface. Reliably distribute data from any compatible software or hardware controller. Use USB or Art-Net for all the great features of the MADRIX software. MADRIX Sync Mode Simply use several units at the same time for larger projects. Only MADRIX software and hardware allow you to fully synchronize Art-Net data for all ports and across multiple devices to get an optimal image on the LEDs without visual interruptions. Designed For DIN Rails Or Walls Its non-conductive enclosure and standardized design for 35 mm top-hat rails make mounting quick, easy, and safe. 2 extra brackets are provided for optional wall mounting. 6 indicators quickly show the device status with the option to turn them off. Invaluable Features The device is ready within seconds after startup. Its firmware is upgradable for future features. HTP Merging is automatically available for two Art-Net sources. Use the built-in web tool for configuration. Connectivity- 2x OUT (screw terminals)
- 1x RJ45 Ethernet port
- 1x USB port
- 1x Power (screw terminal)
- MADRIX NEBULA
- Set of screw terminals (2x 4-pin and 1x 2-pin)
- USB cable
- MADRIX software (license not included)
- 2 wall-mount brackets
Additional LED types will be supported with future firmware updates. Quick Links: SKU# IA-HW-001018- APA101
- APA102
- APA104
- APA106
- LPD6803
- LPD8806
- SM16703
- SM16716
- TLS3001
- TLS3008
- TM1804
- TM1809
- TM1812
- TM1829
- UCS1903
- WS2801
- WS2803
- WS2811
- WS2812
- WS2812B
-
SKU# IA-HW-001019The MADRIX STELLA is a dedicated control interface for Art-Net and DMX512 that is designed for high quality and practicability in permanent LED installations. Features: Art-Net Node Art-Net data is directly converted to DMX512. Optimize for short distances to your LEDs and decentralize cabling to cover any distance to the device using Ethernet network. Supply power over USB or 5 V to 24 V over a 2-pin screw terminal. 2 DMX-IN/OUT Directly connect DMX512 to the two 3-pin screw terminals to distribute 2 DMX universes per unit as input and/or output, eliminating the need for XLR connectors as a result. Simply use several units at the same time for larger projects. Easy Configuration MADRIX STELLA offers powerful features, especially in combination with MADRIX. Take full advantage of pixel mapping and voxel mapping. Managing the device is still quick and easy. MADRIX Sync Mode Only MADRIX software and hardware allow you to fully synchronize Art-Net data for all output ports and across multiple devices to get an optimal image on the LEDs without visual interruptions. Designed For DIN Rails Or Walls Its non-conductive enclosure and standardized design for 35 mm top-hat rails make mounting quick, easy, and safe. 2 extra brackets are provided for optional wall mounting. 6 indicators quickly show the device status with the option to turn them off. 3rd-Party Controllers MADRIX STELLA complies with the official Art-Net specifications and can be used as a regular Art-Net unit with your other consoles, controllers, or software solutions. MADRIX DMX512 USB Interface Alternatively, you can choose to connect the unit as a plug-and-play solution to your computer and the MADRIX software using any USB 2.0 port. Invaluable Features The device is ready within seconds after startup. HTP Merging is automatically available for two Art-Net sources. You can change specific device settings using the built-in web configuration tool. Connectivity- 2x DMX-IN/OUT (screw terminals)
- 1x RJ45 Ethernet port
- 1x USB port
- 1x Power (screw terminal)
- MADRIX STELLA
- Set of screw terminals (2x 3-pin and 1x 2-pin)
- USB power supply, USB cable, world adapters kit
- MADRIX software (license not included)
- 2 wall-mount brackets
-
SKU# 5050-sb-kitThe Silicone Bracket Kit includes 15 brackets and 30 screws. Used to securely install your 5050 IP67 or IP68 strips. SKU# 5050-SB-KIT -
-
-
SKU# XPD-DMX-AB-SPLITTER-MIXXPD-28 splitters boost, refresh and distribute the DMX signals of two inputs onto eight outputs. This allows for safely going beyond the 32 devices limit of the DMX standard, as well as for building star topologies. Moreover, the XPD-28 can be used as a repeater in order to transport a DMX signal across larger distances just as well. XPD-28-5R8-US 2:8, rack mountable DMX and RDM splitter, inputs: 5-pin XLR, outputs: 3-pin XLR XPD-28-5R2-US 2:8, rack mountable DMX and RDM splitter, inputs 5-pin XLR, outputs: 6 x 5-pin XLR and 2 x 3-pin XLR XPD-28-5R4-US 2:8, rack mountable DMX and RDM splitter, inputs: 5-pin XLR, outputs: 4 x 5-pin XLR and 4 x 3-pin XLR XPD-28-5R6-US 2:8, rack mountable DMX and RDM splitter, inputs 5-pin XLR, outputs: 2 x 5-pin XLR and 6 x 3-pin XLR Features- OLED display.
- Metal button/ potentiometer
- Amplifies/ boosts DMX
- Splits and cleans DMX signal
- RDM Protocol
- Enhanced DMX data regeneration
- Individual optical isolation on all ports
- Realtime DMX monitoring
- DMX Framerate display
- DMX channel overview
- 19″ Rack mountable
-
SKU# XPD-DMX-AB-SPLITTERXPD-28 splitters boost, refresh and distribute the DMX signals of two inputs onto eight outputs. This allows for safely going beyond the 32 devices limit of the DMX standard, as well as for building star topologies. Moreover, the XPD-28 can be used as a repeater in order to transport a DMX signal across larger distances just as well. XPD-28-5R-US 2:8, rack mountable DMX and RDM splitter, 5- pin XLR XPD-28-3R-US 2:8, rack mountable DMX and RDM splitter, 3- pin XLR XPD-28-8R-US 2:8, rack mountable DMX and RDM splitter, RJ45 Features- OLED display.
- Metal button/ potentiometer
- Amplifies/ boosts DMX
- Splits and cleans DMX signal
- RDM Protocol
- Enhanced DMX data regeneration
- Individual optical isolation on all ports
- Realtime DMX monitoring
- DMX Framerate display
- DMX channel overview
- 19" Rack mountable
-
SKU# XSR-OPTO-SPLITTER-MIXThe Swisson XSR line of Opto-Splitters are all highly reliable DMX and RDM splitters and boosters with specially designed power supplies to ensure safe operation, even under harsh conditions. With individually optically isolated ports, these splitters are less susceptible to voltage spikes. These RDM & DMX Opto-Splitters boost, regenerate, and distribute both DMX & RDM signals. The Swisson XSR Opto-Splitters are perfect for projects that require demanding DMX performance. XSR-5R2-5R2-US The RDM & DMX Opto-Splitter 5 Pin XLR In & Thru – three 5 Pin and two 3 Pin XLR Out Double Rack is capable of being mounted with the included flanges, equipped with two 5 Pin XLR inputs, two 5 Pin XLR through ports, six 5 Pin XLR outputs and four 3 Pin XLR outputs. XSR-5R-5R5-US The RDM & DMX Opto-Splitter 5 Pin XLR In & Thru – five 5 Pin and five 3 Pin XLR Out Double Rack is capable of being mounted with the included flanges, equipped with two 5 Pin XLR inputs, two 5 Pin XLR through ports, five 5 Pin XLR outputs and five 3 Pin XLR outputs. XSR-5R-3R-US The RDM & DMX Opto-Splitter 5 and 3 Pin XLR In & Thru – five 5 Pin and five 3 Pin XLR Out Double Rack is capable of being mounted with the included flanges, equipped with one 5 Pin and one 3 Pin XLR input, one 5 Pin and one 3 Pin XLR through port, five 5 Pin XLR outputs and five 3 Pin XLR outputs. Features
- R Switch to toggle between RDM&DMX compatibility or DMX only mode
- LED Display
- ETL/cETL/CE certified
- Optical isolation prevents signal disturbances
- Isolation between input and outputs as well as full isolation between each output
- Simplify connections and reduce installation and cable cost
- Easy detection of disturbances by intelligent DMX protocol supervisor
- Clean and clear amplification of DMX signals
- DMX line can be terminated by pressing a button
- Extend DMX lines infinitely with the splitter
- Strong Power Supply worldwide 5VAC – 276VAC
- Input (1 universe) 1pcs
- Through (1 universe) 1pcs
- Outputs 5 pcs
- Box version, M10 thread for a clamp and an eye bolt for safety line
- Dimensions Rack: 19″, 1 Unit, 111 mm, Box: 220x111x44mm
- 2 Year warranty
-
SKU# XSR-5R2-USThe Swisson XSR line of Opto-Splitters are all highly reliable DMX and RDM splitters and boosters with specially designed power supplies to ensure safe operation, even under harsh conditions. With individually optically isolated ports, these splitters are less susceptible to voltage spikes. These RDM & DMX Opto-Splitters boost, regenerate, and distribute both DMX & RDM signals. The Swisson XSR Opto-Splitters are perfect for projects that require demanding DMX performance. Swisson XSR-5R2-US The RDM & DMX Opto-Splitter 5 Pin XLR In & Thru – 3-5 Pin and 2-3 Pin Out XLR Single Rack includes hardware for mounting onto racks, one 5 Pin XLR input, one 5 Pin XLR through, three 5 Pin XLR outputs and two 3 Pin XLR outputs. Features- R Switch to toggle between RDM&DMX compatibility or DMX only mode
- LED Display
- ETL/cETL/CE certified
- Optical isolation prevents signal disturbances
- Isolation between input and outputs as well as full isolation between each output
- Simplify connections and reduce installation and cable cost
- Easy detection of disturbances by intelligent DMX protocol supervisor
- Clean and clear amplification of DMX signals
- DMX line can be terminated by pressing a button
- Extend DMX lines infinitely with the splitter
- Strong Power Supply worldwide 5VAC – 276VAC
- Input (1 universe) 1pcs
- Through (1 universe) 1pcs
- Outputs 5 pcs
- Box version, M10 thread for a clamp and an eye bolt for safety line
- Dimensions Rack: 19″, 1 Unit, 111 mm, Box: 220x111x44mm
- 2 Year warranty
-
SKU# XSP-OPTO-SPLITTER-MIXDMX splitters are the backbone of any DMX512 installation. The XSP series of splitters offer the highest level of reliability for professional use for events or on installations. The specially designed power supply ensures safe operation even under harsh mains conditions. Each port is optically isolated and very well protected against transient over voltages. Swisson-XSP-5R2-5R2-US The DMX Opto-Splitter 5 Pin XLR In & Thru – three 5 Pin and two 3 Pin XLR Out Double Rack is capable of being mounted with the included flanges, equipped with two 5 Pin XLR inputs, two 5 Pin XLR through ports, six 5 Pin XLR outputs and four 3 Pin XLR outputs. Swisson-XSP-5R-5R5-US The DMX Opto-Splitter 5 Pin XLR In & Thru – five 5 Pin and five 3 Pin XLR Out Double Rack is capable of being mounted with the included flanges, equipped with two 5 Pin XLR inputs, two 5 Pin XLR through ports, five 5 Pin XLR outputs and five 3 Pin XLR outputs. Swisson-XSP-5R-3R-US The DMX Opto-Splitter 5 and 3 Pin XLR In & Thru – five 5 Pin and five 3 Pin XLR Out Double Rack is capable of being mounted with the included flanges, equipped with one 5 Pin and one 3 Pin XLR input, one 5 Pin and one 3 Pin XLR through port, five 5 Pin XLR outputs and five 3 Pin XLR outputs. Features- ETL/cETL/CE certified
- Optical isolation prevents signal disturbances
- Isolation between input and outputs as well as full isolation between each output
- Simplify connections and reduce installation and cable cost
- Easy detection of disturbances by intelligent DMX protocol supervisor
- Clean and clear amplification of DMX signals
- DMX line can be terminated by pressing a button
- Extend DMX lines infinitely with the splitter
- Strong Power Supply worldwide 5VAC – 276VAC
- Input (1 universe) 1pcs
- Through (1 universe) 1pcs
- Outputs 5 pcs
- Box version, M10 thread for a clamp and an eye bolt for safety line
- Dimensions Rack: 19″, 1 Unit, 111 mm, Box: 220x111x44mm
- 2 Year warranty
-
SKU# XSP-5R2-USDMX splitters are the backbone of any DMX512 installation. The XSP series of splitters offer the highest level of reliability for professional use for events or on installations. The specially designed power supply ensures safe operation even under harsh mains conditions. Each port is optically isolated and very well protected against transient over voltages. Swisson-XSP-5R2-US The DMX Opto-Splitter 5 Pin XLR In & Thru – 3- 5 Pin and 2- 3 Pin XLR Out Single Rack is a rack mountable Opto-Splitter equipped with flanges on both ends, one 5 Pin XLR input, one 5 Pin XLR through, three 5 Pin XLR outputs and two 3 Pin XLR outputs. Features- ETL/cETL/CE certified
- Optical isolation prevents signal disturbances
- Isolation between input and outputs as well as full isolation between each output
- Simplify connections and reduce installation and cable cost
- Easy detection of disturbances by intelligent DMX protocol supervisor
- Clean and clear amplification of DMX signals
- DMX line can be terminated by pressing a button
- Extend DMX lines infinitely with the splitter
- Strong Power Supply worldwide 5VAC – 276VAC
- Input (1 universe) 1pcs
- Through (1 universe) 1pcs
- Outputs 5 pcs
- Box version, M10 thread for a clamp and an eye bolt for safety line
- Dimensions Rack: 19″, 1 Unit, 111 mm, Box: 220x111x44mm
- 2 Year warranty
-
SKU# LED-TUB-XX3M™ Heat Shrink Tubing offers an outstanding balance of electrical, physical and chemical properties for a wide variety of industrial and military applications. Rated for 135°C continuous operation, all tubing is split resistant, mechanically tough, easily marked and resists cold flow. Typically used as a shrink-fit electrical insulation over cable splices and terminations. Great for use with 5050 LED Strip leads. It is also used for lightweight wire harness covering, wire marking, wire bundling, component packaging and fire-resistant covering. Please Note: This item is sold Per Feet SKU# LED-TUB-XX -
SKU# LED-PS24V-90W-ULImportant Features:- High efficiency, up to 91%
- Protection against short circuit, over current, over voltage and over temperature
- Class II power unit, no FG
- UL Listed, suitable for dry and damp locations
- Waterproof IP67
- 5 years warranty
- For use in the USA & Europe
- Indoor LED lighting
- LED decorative lighting
- LED office lighting
- General electronic products in dusty or humid environments
-
SKU# LED-PS12V-60W-ULImportant Features:- High efficiency, up to 91%
- Protection against short circuit, over current, over voltage and over temperature
- Class II power unit, no FG
- Class 2 Power Supply
- UL Listed, suitable for dry and damp locations
- Waterproof IP67
- 5 years warranty
- For use in the USA & Europe
- Indoor LED lighting
- LED decorative lighting
- LED office lighting
- General electronic products in dusty or humid environments
-
SKU# MOD-XXXXDMX Modules for CueServer 2 Pro (CS-900) add physical DMX inputs or outputs. SKU# MOD-XXXX -
SKU# dmx-venue-packIntroducing our NEW DMX LED Strip Venue Lighting Kits. Each kit is different, however all of them come with the same basic components allowing you to choose from a simple economical set-up, to a more elaborate DMX pixel by pixel controlled LED Strip installation. With each of these kits (and your imagination), you can turn your business, church, or home into a vibrant new setting while providing endless possibilities and design options. There are up to four different packages to choose from ranging from "Basic" to "Ultimate Plus,” each being customizable to best fit your project's specific needs as well as your budget. Give us a call today and we will help to choose the best Venue Kit suited for your needs. View specific package details: Basic | Pro | Ultimate | Ultimate+Basic
This DMX pixel-by-pixel LED package is suitable for either 16 rays of 4 foot LED Strips or 8 rays of 8 foot LED Strips. **Please note that these packages do not contain any type of metal structure** Package Contains:- 1 - MADRIX License Key - Entry
- 1 - Artnet to DMX Controller 6 Universes AD-PRO-6
- 4 - DMX LED Strip 34 Pixel/m RGB SIRS-E Pixel DMX Controlled
- 8 - LED Power Supply 30 Watts 5 Volts
- 32 - ft. of Wire 14 AWG Hook-Up Wire Red & Black For LED Power Supply
- 20 - ft. of RGBW LED Strip Wire 20 AWG RGB 5 Wire Conductors Cable
- 4 - DMX 5 Pin XLR Neutrik 20 ft. Cable
- 1 Hour of Technical Supports
Pro
This DMX pixel-by-pixel LED package is suitable for either 32 rays of 4 foot LED Strips, 16 rays of 8 foot LED Strips or 8 rays of 16 foot LED Strips. Package Contains:- 1 - MADRIX License Key - Entry
- 2 - Artnet to DMX Controller 6 Universes AD-PRO-6
- 8 - DMX LED Strip 34 Pixel/m RGB SIRS-E Pixel DMX Controlled
- 16 - LED Power Supply 30 Watts 5 Volts
- 64 - ft. of Wire 14 AWG Hook-Up Wire Red & Black For LED Power Supply
- 40 - ft. of RGBW LED Strip Wire 20 AWG RGB 5 Wire Conductors Cable
- 8 - DMX 5 Pin XLR Neutrik 20 ft. Cable
- 2 Hours of Technical Support
Ultimate
This DMX pixel-by-pixel LED package is suitable for either 64 rays of 4 foot LED Strips, 32 rays of 8 foot LED Strips or 16 rays of 16 foot LED Strips. Package Contains:- 1 - MADRIX License Key - Basic
- 3 - Artnet to DMX Controller 6 Universes AD-PRO-6
- 16 - DMX LED Strip 34 Pixel/m RGB SIRS-E Pixel DMX Controlled
- 32 - LED Power Supply 30 Watts 5 Volts
- 128 - ft. of Wire 14 AWG Hook-Up Wire Red & Black For LED Power Supply
- 60 - ft. of RGBW LED Strip Wire 20 AWG RGB 5 Wire Conductors Cable
- 16 - DMX 5 Pin XLR Neutrik 20 ft. Cable
- 3 Hours of Technical Support
Ultimate Plus
This DMX pixel-by-pixel LED package is suitable for either 128 rays of 4 foot LED Strips, 64 rays of 8 foot LED Strips or 32 rays of 16 foot LED Strips. Package Contains:- 1 - MADRIX License Key - Basic
- 6 - Artnet to DMX Controller 6 Universes AD-PRO-6
- 32 - DMX LED Strip 34 Pixel/m RGB SIRS-E Pixel DMX Controlled
- 64 - LED Power Supply 30 Watts 5 Volts
- 256 - ft. of Wire 14 AWG Hook-Up Wire Red & Black For LED Power Supply
- 80 - ft. of RGBW LED Strip Wire 20 AWG RGB 5 Wire Conductors Cable
- 32 - DMX 5 Pin XLR Neutrik 20 ft. Cable
- 4 Hours of Technical Support
-
SKU# LED-PLUG-2MFLED strip and power supply 2 wire plug. Easy installation with only 2 screws. No soldering, splicing or crimping required. Great for multiple uses including:- Single Color LED Strips
- DMX LED Strip Power
- Power Supplies
- Custom Power Cables
- 38mm x 14mm x 13mm
- External Diameter: 5.5mm
- Internal Diameter: 2.1mm
-
SKU# AD-PRO-6-BKTech Specs:- 1 - DB-15 Male Connector
- 6 - 5 Pin XLR Female Neutrik Connectors
- Length: 19"
- Color: Black (white XLR cable segments)
- Made with High Quality Horizon Cable
- Made with High Quality Neutrik Connectors
- Complies with DMX512 USITT standards
- Made in the USA.
-
SKU# AD-PRO-6-PSTech Specs:- 1 -Type A Electrical Male Plug
- 1 -2.5MM sealed IP68 Power Plug
- Input: AC 120V
- Output: DC 12V
- Current: 1.25A
- Length: 68"
- Color: Black (White XLR Cable)
- Made with High Quality Switchcraft Components
- Assembled in the USA.
-
SKU# LED-RTV-SILOverview: Reseal your waterproof LED Strips with this clear silicone sealant. This non-toxic, non-polluting sealant is great for electronic components. This product works at room temperature with metal and non metal materials. It is also excellent when used as a form of electrical insulation/resistance, aging resistance, and moisture proofing. This product is tested to work with all SIRS-E Waterproof strips and Waterproof End Caps. Applications: Used for bonding, sealing, or insulating of:- Electronics
- Semiconductor materials
- Electrical equipment
- Magnetic tile
- Optical instruments
-
SKU# ECXXX-PK10Overview: Complete your waterproof LED tape (strip) lighting applications with waterproof endcaps for your leads and tales. These standard endcaps are useable for tape lighting with 10mm and 12 mm width flexible PCBs with options for with or without holes. Solid endcaps can be used to terminate ends where “no” protruding wires will be present. Endcaps with holes can be used where protruding wires “will” be present for lead wires used to run power and/or data signal. All endcaps will require a silicone sealant to bond and secure cappings into place. Applications: For use with IP67 (silicone sleeved) or IP68 (silicone extruded/injected) tape lighting. Accessories: Clear RTV Silicone Sealant #LED-RTV-SIL Silicone Bracket #5050-sb-kit ** End Cap with Holes may require slight modification in order to accommodate various LED strip wire configurations. Package Contains 10 End Caps End Caps Datasheet SKU# ECXXX-PK10 -
SKU# DMX-TUBE-PROGTech Specs:- Color: Black
- Address Input: Manual
- Display: Digital Display
- Data Output: XLR 3-Pin Female
- Control: DMX512 Protocol
- Power Requirement: 12V DC
- Part Number: DMX-TUBE-PROG
-
SKU# DIN-HMBKit for mounting CS-810, CS-816 horizontally on DIN Rail. SKU# DIN-HMB -
SKU# 5050-CON-C5C55050 RGBW LED Strip Bridge Coupler (Quick Connect), 12mm wide. Used to join 5050 RGBW SMD LED Strips together. SKU# 5050-CON-C5C5 -
SKU# 5050-CON-C5W- 5050 RGBW LED Strip Coupler (Quick Connect) with Lead
- The 5050-CON-C5W-L connects the Lead side of the LED strip with lead wires
- The 5050-CON-C5W-T connects the Tail side of the LED strip with tail wires
- 12mm wide
- 12 in long wire
- Used for applying lead at beginning or end of a 5050 RGBW SMD LED Strip
-
SKU# 5050-CON-C5WC5- Connector for 5050 LED RGBW strip to strip
- 12mm wide
- 12 in long wire
-
SKU# ART500The Art 500 is a touch panel DMX Controller with 1,024 DMX channels and 500 programmable scenes, designed to be the most effective control solution for architectural control. Included is the ART 500 software package, which others an easy-to-navigate interface combined with powerful control features. Not only can it be controlled remotely from an iPhone or iPad, but the ART500 is capable of learning sunset and sunrise times with integrated GPS coordination. This feature is excellent for installations that automatically need to light on at a certain time without relying on a photocell switch or other similar devices. Also available on the beautiful slim touch panel is an LCD screen which allows you to read all the different zones depending on how the user may have labeled them. Also, add pictures of the different zones in your installation displayed on the LCD, making it even easier to recognize which zone you select. Available in black and white colors, the ART500 is ready to bring any room into life with unparalleled lighting control. WHAT'S IN THE PACKAGE?- ART500 Controller
- USB Cable
- Micro SD Card
- Power Adapter
-
SKU# SWISSON-XWL-TR- XWL-T-CRMX-3: 3-Pin XLR CRMX Wireless DMX Transmitter
- XWL-T-CRMX-5: 5-Pin XLR CRMX Wireless DMX Transmitter
- XWL-R-CRMX-3: 3-Pin XLR CRMX Wireless DMX Receiver
- XWL-R-CRMX-5: 5-Pin XLR CRMX Wireless DMX Receiver
- XWL-T-W-DMX-3: 3-Pin XLR W-DMX Wireless DMX Transmitter
- XWL-T-W-DMX-5: 5-Pin XLR W-DMX Wireless DMX Transmitter
- XWL-R-W-DMX-3: 3-Pin XLR W-DMX Wireless DMX Receiver
- XWL-R-W-DMX-5: 5-Pin XLR W-DMX Wireless DMX Receiver
Several transmitters can be operated in parallel, each of which is easily linkable to any number of receivers and capable of handling one full universe of 512 DMX channels.
All XWL products are equipped with M10/M12 and 3/8" threads to provide a variety of installation possibilities, such as mounting on a microphone stand.
- Wireless DMX receiver (XWL-R models)
- Wireless DMX transmitter (XWL-T models)
- Available with W-DMX™ or CRMX™
- M10/M12 threads for truss mount
- 3/8” thread for mounting on a microphone stand
- Built-in power supply (powerCON connected)
- Compact, rugged housing
-
SKU# XSW-TR-SERIES2 Year Warranty The XSW combines CRMX wireless DMX technology with our entire line of DMX splitters. The XSW can operate as a DMX transmitter or as a DMX receiver at the press of a button. The DMX splitter functionality is always available regardless of whether the device is configured as a transmitter or receiver. If only the splitter function is used, the wireless part is switched off. The splitter offers one input port, a thru port and 4 individually optically isolated output ports. Multiple radio links can be operated at the same time, allowing a setup with multiple DMX Universes. Multiple receivers can be connected to a single transmitter. A variety of wireless configurations can be built up with the same XSW components.- XSW-TR-CRMX-3B: 3-Pin XLR CRMX Transceiver Box
- XSW-TR-CRMX-3R: 3-Pin XLR CRMX Transceiver Single Rack
- XSW-TR-CRMX-5B: 5-Pin XLR CRMX Transceiver Box
- XSW-TR-CRMX-5R: 5-Pin XLR CRMX Transceiver Single Rack
- XSW-TR-W-DMX-3B: 3-Pin XLR W-DMX Transceiver Box
- XSW-TR-W-DMX-3R: 3-Pin XLR W-DMX Transceiver Single Rack
- XSW-TR-W-DMX-5B: 5-Pin XLR W-DMX Transceiver Box
- XSW-TR-W-DMX-5R: 5-Pin XLR W-DMX Transceiver Single Rack
-
SKU# SWISSON-DIN-RAIL- ISP-4D-TERM: DMX DIN Rail Splitter Program; 4-Outputs, PLUGGABLE SCREW TERMINALS ISP-4D-RJ45A: DMX DIN Rail Splitter Program; 4-Outputs, RJ45A DMX, PINOUT ANSI E1.11 (1:+, 2:-, 7&8:COM) ISP-4D-RJ45B: DMX DIN Rail Splitter Program; 4-Outputs, RJ45B DMX, PINOUT ALTERNATIVE (1:-, 2:+, 3:COM)
- ISP-4R-TERM: RDM DIN Rail Splitter Program; 4-Outputs, PLUGGABLE SCREW TERMINALS ISP-4R-RJ45A: RDM DIN Rail Splitter Program; 4-Outputs, RJ45A DMX, PINOUT ANSI E1.11 (1:+, 2:-, 7&8:COM) ISP-4R-RJ45B: RDM DIN Rail Splitter Program; 4-Outputs, RJ45B DMX, PINOUT ALTERNATIVE (1:-, 2:+, 3:COM)
- DMX splitter / booster
- DMX repeater
- LED display; signal, power, RDM
- Input optically isolated
- Each output individually optically isolated
- RDM support (optional)
- Extend DMX lines infinitely with the splitter
- Rugged metal housing
- Built-in termination
- RJ-45 and pluggable screw terminal variants
- DC power input, 10-48V DC, max. 400mA
- Isolation between input and outputs as well as full isolation between each output
- Dimensions: L=125mm, W=90mm, H=56mm
- 2 Year Warranty
-
SKU# LED-CAB-PWR2 Pin red-black connectors Male or Female, 20AWG, 12 in wire length LED-CAB-2M-PWR: Male LED-CAB-2F-PWR: Female Quick Links: SKU# LED-CAB-PWR -
SKU# IA-HARD-001013MADRIX® USB light sensor This sensor measures the ambient light level. The small unit can simply be connected to any USB 2.0 port. Incoming values are directly translated into DMX data in MADRIX® as well as percent. Example of use: Master Fader SKU# IA-HARD-001013 -
SKU# IA-HARD-001012MADRIX® USB temperature This small and durable sensor measures the temperature. The small unit can simply be connected to any USB 2.0 port. Incoming temperature values are directly translated into DMX data in MADRIX® as well as degree Celsius or degree Fahrenheit. Example of use: SCE Ticker. SKU# IA-HARD-001012 -
SKU# IA-HARD-001011MADRIX® USB contact closure This digital input device registers if its circuit is either open or closed. In most cases, it is used to build a switch or trigger. The small unit can simply be connected to any USB 2.0 port. Incoming values are directly translated into DMX data in MADRIX®. Example of use: Strobe or Blackout. SKU# IA-HARD-001011
ShopMark Eviota2024-04-02T12:17:21-05:00
