Main 281-324-0908  |  9AM - 6PM M-F (CDT)
  •

    Madrix USB ONE

    SKU# IA-HW-001001
    Important Links:

    The USB ONE allows you to control 512 DMX channels via Madrix software.

    • DMX-IN/OUT with 5-pin NEUTRIK XLR Port: This device allows you to send or receive data via MADRIX using 512 DMX channels. A gender changer with 5-pin male to 3-pin or 5-pin male is required for DMX-IN.
    • USB 2.0 Standard: The latest USB 2.0 standard is fully supported to allow for a higher maximum speed of 480Mbit/s.
    • Power Over USB: The interface is powered directly via the USB port and does not need an additional power supply.
    • Hot Swapping & Plug and Play: Devices can be connected to and disconnected from the computer during use and without a reboot.
    • Remote Control: MADRIX can be controlled remotely using the built-in DMX-IN functions.
    • Frame Rate Stability: Up to 60 devices can be connected to a single USB host controller without having any frame rate problems (60 DMX512 interfaces amount to 30,720 DMX channels).
    • Active USB: Must be connected to an active USB 2.0 hub with a power supply.
    SKU# IA-HW-001001
    Details

  • MADRIX USB Temperature

    SKU# IA-HARD-001012
    MADRIX® USB temperature This small and durable sensor measures the temperature. The small unit can simply be connected to any USB 2.0 port. Incoming temperature values are directly translated into DMX data in MADRIX® as well as degree Celsius or degree Fahrenheit. Example of use: SCE Ticker. SKU# IA-HARD-001012
    Details

  • NEUTRIK 4 Pole XLR Receptacle P Series, Female

    SKU# NC4FP-1
    TECHNICAL DATA Electrical
    • Number of contacts: 3 - 7 (except MP: 3-6)
    • Rated voltage: 50 V ac
    • Contact resistance: < 5 m
    • Insulation resistance - initial: > 2 G
      • - after damp heat test: > 1 G
      • -IEC 68-2-30)
    • Dielectric strength: 1500 V dc
    • Rated current:
    • 3 pole: 16 I [A], 2.5/14 mm2/AWG, ≤ 4 C
    • 4 pole: 10 I [A], 1.5/16 mm2/AWG, ≤ 7 C
    • 5 and 6 pole: 7.5 I [A], 1.0/18 mm2/AWG, ≤ 7 C
    • 7 pole: 5 I [A], 1.0/18 mm2/AWG, ≤ 9 C
    I ... Rated current per contact C ... Capacitance between contacts Mechanical
    • Lifetime: > 1000 mating cycles
    • Insertion / withdrawal force: ≤ 20 N
      • Retention method (Female versions only): - standard: latch lock
    • "-0" version: retention spring
    • Separating force: ≤ 20 N
    Materials
    • Shell: ZnAl4Cu1, gal Ni or black Cr plating
    • Insert: PA 6.6 30% GR (glass reinforced)
    • Contacts: - female (3 pole): CuSn6
      • female (4-7pole) & male: CuZn39Pb3
    • Contact surface: gal 2 µm Ag or gal 0.2 µm Au hard alloy over 2 µm Ni
    • Latch lock & spring: CK 67 steel, treated
    Environmental
    • Temperature range: -30° C to + 80° C
    • Flammability: UL 94HB
    • Solderability: complies with IEC 68-2-20
    Compatibility: Switchcraft® DxM, DxF Cannon XLRx31, XLRx32, dimensionally with D series SKU# NC4FP-1
    Details

  • Neutrik NAC3FCA Powercon Cable End Power In

    SKU# NAC3FCA
    Lockable cable connector, power-in, screw terminals, blue The powerCON is a locking 3 conductor equipment AC connector with contacts for line, neutral and pre-mating ground contact. It replaces appliance couplers wherever a very rugged solution in combination with a locking device is needed in order to guarantee a safe power connection. Attention: The powerCON is a connector without breaking capacity, i.e. the powerCON should not be connected or disconnected under load or live! Features & Benefits
    • Locking 20 A / 250 V ac appliance coupler
    • 3 contacts for line, neutral and premating safety ground
    • Power-in (blue) and power-out (grey) versions with different keying to avoid the possibility of intermating
    • Fast and easy twist lock latching system
    • Extremely robust and reliable
    • Ergonomic design
    • User friendly latch design for easy handling
    • Unique Neutrik chuck type strain relief
    • UL, cUL recognized components
    • VDE certified
    • SEV approved
    • Branded with unique hologram - guarantees genuine and authentic Neutrik product
    NAC3FCA-pieces Note: Item comes disassembled Quick Links: SKU# NAC3FCA
    Details

  • Neutrik NAC3FCB Powercon Cable End Power Out

    SKU# NAC3FCB
    Lockable cable connector, power-out, screw terminals, grey The powerCON is a locking 3 conductor equipment AC connector with contacts for line, neutral and pre-mating ground contact. It replaces appliance couplers wherever a very rugged solution in combination with a locking device is needed in order to guarantee a safe power connection. Attention: The powerCON is a connector without breaking capacity, i.e. the powerCON should not be connected or disconnected under load or live! Features & Benefits
    • Locking 20 A / 250 V ac appliance coupler
    • 3 contacts for line, neutral and premating safety ground
    • Power-in (blue) and power-out (grey) versions with different keying to avoid the possibility of intermating
    • Fast and easy twist lock latching system
    • Extremely robust and reliable
    • Ergonomic design
    • User friendly latch design for easy handling
    • Unique Neutrik chuck type strain relief
    • UL, cUL recognized components
    • VDE certified
    • SEV approved
    • Branded with unique hologram - guarantees genuine and authentic Neutrik product
    Quick Links: NAC3FCB-pieces
    Note: Item comes disassembled
    SKU# NAC3FCB
    Details

  • Neutrik NAC3MPA Powercon Chasis Connector Power In

    SKU# NAC3MPA
    Chassis connector, power-in, 3/16'' flat tab terminals, blue The powerCON is a locking 3 conductor equipment AC connector with contacts for line, neutral and pre-mating ground contact. It replaces appliance couplers wherever a very rugged solution in combination with a locking device is needed in order to guarantee a safe power connection. Attention: The powerCON is a connector without breaking capacity, i.e. the powerCON should not be connected or disconnected under load or live! Features & Benefits
    • Locking 20 A / 250 V ac appliance coupler
    • 3 contacts for line, neutral and premating safety ground
    • Power-in (blue) and power-out (grey) versions with different keying to avoid the possibility of intermating
    • Fast and easy twist lock latching system
    • Extremely robust and reliable
    • Ergonomic design
    • User friendly latch design for easy handling
    • UL, cUL recognized components
    • VDE certified
    • SEV approved
    • Branded with unique hologram - guarantees genuine and authentic Neutrik product
    Quick Links: SKU# NAC3MPA
    Details

  • Neutrik NAC3MPB Powercon Chasis Connector Power Out

    SKU# NAC3MPB
    Chassis connector, power-out, 3/16'' flat tab terminals, grey The powerCON is a locking 3 conductor equipment AC connector with contacts for line, neutral and pre-mating ground contact. It replaces appliance couplers wherever a very rugged solution in combination with a locking device is needed in order to guarantee a safe power connection. Attention: The powerCON is a connector without breaking capacity, i.e. the powerCON should not be connected or disconnected under load or live! Features & Benefits
    • Locking 20 A / 250 V ac appliance coupler
    • 3 contacts for line, neutral and premating safety ground
    • Power-in (blue) and power-out (grey) versions with different keying to avoid the possibility of intermating
    • Fast and easy twist lock latching system
    • Extremely robust and reliable
    • Ergonomic design
    • User friendly latch design for easy handling
    • UL, cUL recognized components VDE certified SEV approved
    • Branded with unique hologram - guarantees genuine and authentic Neutrik product
    Quick Links: SKU# NAC3MPB
    Details
  • OCTO Mk2 - LED Pixel Controller

    OCTO Mk2 – LED pixel controller

    SKU# 71521
    8-Universe DIN rail LED pixel controller The OCTO is the NextGen DIN-rail LED pixel controller -> a pixel data converter & controller capable of controlling up to 1360 RGB LED pixels. Downloadable Documentation: Knowledge Base & FAQ's Supported LED Protocols Hi-Res Images Technical Drawings / Dimensions Release Notes Documents 0.3 & firmware v4.0 are for OCTO MK2 with serial numbers 2374307 onwards only Datasheet 0.3 User Manual 0.3 Firmware v4.0 Custom Protocol Creation Guide 0.3 Documents 0.2 & firmware v3.1 are for OCTO MK2 with serial numbers 2341008 - 2350677 only (**Factory reset before updating to V3.1 for a smooth update) Datasheet 0.2 User Manual 0.2 Firmware v3.1 Documents 0.1 & firmware v2.1 are for OCTO MK2 with serial numbers 2318635 - 2323030 only Datasheet 0.1 User Manual 0.1 Firmware v2.1
    Details
  • ODE Mk3

    ODE Mk3

    SKU# 70407
    The ultimate Power Over Ethernet DMX interface The ODE MK3 is a robust, reliable, installation-grade, Ethernet to DMX converter engineered to connect DMX fixtures to your Ethernet network infrastructure. Now you can expand your lighting project to the next level. With two Universes of bi-directional eDMX to DMX conversion and Art-RDM support, the ODE MK3 is compatible with a wide range of devices and allows for fast deployment of your DMX system. Simply connect, configure and take control! Additionally, this Ethernet to DMX/RDM gateway is packed with installer-friendly features for a speedy installation and configuration, all managed through a web UI – and contained in a compact, portable form factor. With 2 Universes of Ethernet to DMX conversion featuring Art-RDM support, Power over Ethernet (PoE) or a flexible 12-24v DC input, the ODE MK3 allows for fast deployment of DMX systems compatible with a wide range of devices. Downloadable Documentation: Datasheet User Manual Technical Drawing Firmware V1.4 Release Notes
    Details
  • Pharos Hardware

    Pharos Expert Hardware

    SKU# XPC-1
    PHAROS In stock and ready to ship! Video: Pharos Expert Quick Presentation by SIRS-E High Quality DMX Touch Screen With the reliability you expect from Pharos and the expertise in dynamic lighting in architecture and entertainment: an easy to install, easy to use control solution. XPC 1 - Expert Control 1 (Lighting controller with 512 channels eDMX/DMX, DALI, IO) XPC 2 - Expert Control 2 (Lighting controller with 1,024 channels eDMX/DMX, DALI, IO) XPR - Expert Repeat (DMX Splitter with 1 in, 4 out, 24V DC) XPS - Expert Switch (Unmanaged PoE Ethernet switch with 4 Port, Class 2 PoE, 24V DC) XPT 5 W - Expert Touch 5 White (5” wall mount touchscreen interface) † *
    • 5 Year Warranty
    • Installer Friendly
    • Reliability
    • Free Software
    Details
  • Pixelator Mini

    Pixelator Mini – 16 Universe Ethernet to Pixel Converter

    SKU# 70067
    A smart, cost-effective lighting control solution, the Pixelator Mini is a compact 16 Universe rack, surface & DIN-rail mountable, eDMX to LED pixel protocol converter. Control LED pixels with ease ENTTEC’s Pixelator Mini is an installation-grade Ethernet pixel converter designed to make control of LED pixel dots and strip simple. In total, the Pixelator Mini can convert up to 8,192 channels (2,730 RGB pixels) across its 8 PLink outputs (2 Universes per port) with perfect synchronisation across each. The Pixelator Mini acts as the head end of ENTTEC’s PLink control system. The PLink data it generates can be sent up to 300m using standard CAT6 cabling to plug into ENTTEC’s compact power injection modules and LED dimmers. Flexibility is at the heart of the design. Power the Pixelator Mini using either the DC power supply included in the box or by using PoE. Install it using one of the four mounting options included in the box, then configure and update it from anywhere on your network using its intuitive web interface. Downloadable Documentation: Pixelator Mini Datasheet User Manual Firmware (Note: This firmware is not backward compatible with the 70066 Pixelator Mini)
    Details
  • PLink Injector

    PLink Injector

    SKU# 7354X
    The smart way to connect your Pixel lights The PLink Injector has been engineered to work alongside your Pixelator to extend your LED pixel layout over long distances. The PLink Injector has been engineered to work as part of an ENTTEC Pixelator Series set up to make it fast, easy and affordable for you to control LED pixel strips or pixel dots over long distances. The injector features an external DC power supply as well as high-power screw terminal connectors. In addition, they are ideal for custom shape pixel LED installations and their scalable design is perfect for large projects. You can choose from the 5V or 12-24V options depending upon your layout. Then simply re-inject power from an external source, and you’re away! Depending on your applications, our Plink Injector comes also in a rugged IP66-rated version, ideal for extreme weather conditions and outdoor installations. Downloadable Documentation: PLink Datasheet PLink Application Diagram
    Details

  • Power Supply for AD-PRO-6 (Replacement)

    SKU# AD-PRO-6-PS
    Tech Specs:
    • 1 -Type A Electrical Male Plug
    • 1 -2.5MM sealed IP68 Power Plug
    • Input: AC 120V
    • Output: DC 12V
    • Current: 1.25A
    • Length: 68"
    • Color: Black (White XLR Cable)
    Overview: The AD-PRO-6 Power Supply is a custom-built power source for the AD-PRO-6. This unit can be used a replacement power supply for your PRO controller or as a backup for your current power supply. It is assembled with high quality materials in the USA. This power supply is included with the purchase of the AD-PRO-6 ArtNet to DMX PRO Controller. Features
    • Made with High Quality Switchcraft Components
    • Assembled in the USA.
    Quick Links: SKU# AD-PRO-6-PS
    Details
  • S-PLAY Smart Light Show Controller

    S-PLAY Smart Light Show Controller

    SKU# 70092
    The revolutionary smart show controller for hassle-free, professional light shows and automated projects. Engineered for projects that require precise automation, the S-PLAY smart light show controller is your all-in-one solution for the creation, recording, triggering, and activation of not only light shows but video, non-lighting events, and much more. Play back multiple shows simultaneously and install it virtually anywhere with flexible mounting options. Downloadable Documentation: Datasheet User Manual OSC API HTTP API TouchOSC Guide Remote Access Guide Specification Firmware: Firmware v2.1.1 Release Notes
    Details

  • SceneStation 3 Series

    SKU# SCENESTATION-3
    SceneStation sets a new standard for full-featured, easy to use, cost-effective DMX lighting control. SceneStation is entirely self-contained in a single gang, wall-switch sized unit. Perfect for restaurants, high-end residential, trade show booths, and more, SceneStation can control nearly any DMX device (RGB fixtures, moving lights, dimmers, effects, etc.), while also remaining very simple for the end user. SS-305 | Architectural SceneStation 3 Includes SceneStation (with a Built-in Effects Engine for creating dynamic scenes), flushplate Unit, pluggable wiring block and mounting hardware. Meant to be wall-mounted. SS-310 | Portable SceneStation 3 Includes SceneStation (with a Built-in Effects Engine for creating dynamic scenes) in a portable enclosure with 5-Pin XLR jacks and power supply (AC-12). Alternate power supply options are available for this product. If you would like to order this product with an Australian Plug Set or a UK/European Plug Set, please include that request on the "Order Notes" section at checkout. SS-315 | Portable SceneStation 3 Kit Includes SceneStation in a portable enclosure with 5-Pin XLR jacks, power supply (AC-12), SceneStation User's Remote and USB StationLink Adaptor, all enclosed in a protective carrying case. Alternate power supply options are available for this product. If you would like to order this product with an Australian Plug Set or a UK/European Plug Set, please include that request on the "Order Notes" section at checkout. Key Features
    • Completely Self-Contained
    • 64 Scene Capacity
    • Static, Sequential, Toggle, Chase, Momentary & Pile-On Modes for Each Button
    • Built-in Effects Engine for creating dynamic scenes
    • Programmable RGB Backlit Buttons
    • Includes 2.4GHz Wireless SceneStation Module
    • DMX-512 Output (44Hz)
    • DMX Input Snapshot and/or Manual Channel Editing
    • IR Remote Setup and Operation
    • Optional "Power-On" Scene Selection
    • AC or DC Operation
    Quick Links: SKU# SCENESTATION-3
    Details

  • SceneStation USB Stick

    SKU# SS-USB-STICK
    For use with SceneStation Studio software for Mac or Windows computers. The SceneStation USB Stick is used on your Mac or PC computer with the free SceneStation Studio software to remotely manage, control and program one or more wireless SceneStations. The adaptor provides the 2.4GHz communication link between the computer and the SceneStation Network. All wireless SceneStations can be protected by a Security PIN to allow only authorized users to be able to control or edit a station. SS-USB-STICK | USB Stick Wireless USB adaptor for use with SceneStation Studio and your Mac or PC.
    Details
  • Storm 8

    Storm 10 – 10-Universe Ethernet to DMX gateway

    SKU# 70057
    Control LED pixels with ease ENTTEC’s Storm10 is a compact, 10-universe installation-grade Ethernet to DMX to DMX/RDM converter designed to make controlling DMX lights over Ethernet simple by effortlessly converting sACN, Art-Net or ESP protocols to DMX512. Install it using one of four mounting options, then configure and update it from anywhere on your network using its intuitive web interface. Its convenient 10 outputs, plus 2 front facing ports make cabling familiar to installers and offers ultimate flexibility if you ever want to expand your infrastructure in the future. With an internal buffer and sync logic you can be confident that with an ENTTEC system you can build vast LED matrixes that span without experiencing any jitter, lag, content tearing or timing issues – ensuring that you stay perfectly synchronised across your entire show. Put simply, everything works as you’d expect it to. Predictability is a good thing. Downloadable Documentation: Datasheet User Manual Firmware (V1.1)
    Details

  • Swisson DIN Rail Splitter Programs

    SKU# SWISSON-DIN-RAIL
    • ISP-4D-TERM: DMX DIN Rail Splitter Program; 4-Outputs, PLUGGABLE SCREW TERMINALS ISP-4D-RJ45A: DMX DIN Rail Splitter Program; 4-Outputs, RJ45A DMX, PINOUT ANSI E1.11 (1:+, 2:-, 7&8:COM) ISP-4D-RJ45B: DMX DIN Rail Splitter Program; 4-Outputs, RJ45B DMX, PINOUT ALTERNATIVE (1:-, 2:+, 3:COM)
    • ISP-4R-TERM: RDM DIN Rail Splitter Program; 4-Outputs, PLUGGABLE SCREW TERMINALS ISP-4R-RJ45A: RDM DIN Rail Splitter Program; 4-Outputs, RJ45A DMX, PINOUT ANSI E1.11 (1:+, 2:-, 7&8:COM) ISP-4R-RJ45B: RDM DIN Rail Splitter Program; 4-Outputs, RJ45B DMX, PINOUT ALTERNATIVE (1:-, 2:+, 3:COM)
    Tech Specs:
    • DMX splitter / booster
    • DMX repeater
    • LED display; signal, power, RDM
    • Input optically isolated
    • Each output individually optically isolated
    • RDM support (optional)
    • Extend DMX lines infinitely with the splitter
    • Rugged metal housing
    • Built-in termination
    • RJ-45 and pluggable screw terminal variants
    • DC power input, 10-48V DC, max. 400mA
    • Isolation between input and outputs as well as full isolation between each output
    • Dimensions: L=125mm, W=90mm, H=56mm
    • 2 Year Warranty
    The ISP-4 splitters also act as repeaters, and thus they may be used for transporting a DMX signal across larger distances. The DMX splitters of the ISP-4 line of products boost an incoming DMX signal and provide it on four output ports. This allows for safely going beyond the 32 devices limit of the DMX standard, as well as for building star topologies. DMX signals often get disturbed by the environment or even by the devices connected to the signal line. An ISP-4 splitter may completely clear the disturbances if it is connected at a location where the signal is still “readable”. Providing four individually optically isolated outputs, as well as an optically isolated input, the ISP-4 splitters may prevent harmful voltages applied to a given port from affecting the other ports and damaging the connected equipment. The bidirectional ISP-4R variants work within DMX / RDM environments, as well as in pure DMX environments. Therefore, ISP-4R splitters are a good solution not only for current RDM users, but also for those who expect to use RDM in the future. The ISP-4D variants on the other hand only work with DMX, while they ignore any RDM data. ISP-4 splitters are DIN rail mountable and powered by an external power supply unit. Quick Links: SKU# SWISSON-DIN-RAIL
    Details

  • Swisson DMX Opto-Splitter

    SKU# XSP-SERIES-SPLITTER
    DMX splitters are the backbone of any DMX-512 installation. The XSP series of splitters offer the highest level of reliability for professional use for events or on installations. The specially designed power supply ensures safe operation even under harsh mains conditions. The XSP box models have a thread for a clamp and an eye for the safety line. These models are portable and suitable for truss mounting. The rack and double rack models are for 19“ rack systems. Customize your purchase by choosing from 3 Pin XLR or 5 Pin XLR inputs and outputs. XSP-3B: The DMX Opto-Splitter Box is equipped with one 3 Pin XLR input, one 3 Pin XLR through, and five 3 Pin XLR outputs. XSP-3R: The DMX Opto-Splitter Single rack is a mountable rack with one 3 Pin XLR input, one 3 Pin XLR through, and five 3 Pin XLR outputs. XSP-3R-3R: The DMX Opto-Splitter Double Rack is a mountable rack containing two 3 Pin XLR inputs, two 3 Pin XLR though ports, and ten 3 Pin XLR outputs XSP-5B: The DMX Opto-Splitter Box is equipped with one 5 Pin XLR input, one 5 Pin XLR through, and five 5 Pin XLR outputs. XSP-5R: The DMX Opto-Splitter Single rack is a mountable rack with one 5 Pin XLR input, one 5 Pin XLR through, and five 5 Pin XLR outputs. XSP-5R-5R: The DMX Opto-Splitter Double Rack is a mountable rack containing two 5 Pin XLR inputs, two 5 Pin XLR though ports, and ten 5 Pin XLR outputs XSP-3B-US: The DMX Opto-Splitter Box is ETL/cETL/CE certified and equipped with one 3 Pin XLR input, one 3 Pin XLR through, and five 3 Pin XLR outputs. XSP-3R-US: The DMX Opto-Splitter Single rack is a ETL/cETL/CE certified mountable rack with one 3 Pin XLR input, one 3 Pin XLR through, and five 3 Pin XLR outputs. XSP-3R-3R-US: The DMX Opto-Splitter Double Rack is a ETL/cETL/CE certified mountable rack containing two 3 Pin XLR inputs, two 3 Pin XLR though ports, and ten 3 Pin XLR outputs XSP-5B-US: The DMX Opto-Splitter Box is ETL/cETL/CE certified and equipped with one 5 Pin XLR input, one 5 Pin XLR through, and five 5 Pin XLR outputs. XSP-5R-US: The DMX Opto-Splitter Single rack is a ETL/cETL/CE certified mountable rack with one 5 Pin XLR input, one 5 Pin XLR through, and five 5 Pin XLR outputs. XSP-5R-5R-US: The DMX Opto-Splitter Double Rack is a ETL/cETL/CE certified mountable rack containing two 5 Pin XLR inputs, two 5 Pin XLR though ports, and ten 5 Pin XLR outputs
    • Optical isolation prevents signal disturbances
    • Isolation between input and outputs as well as full isolation between each output
    • Simplify connections and reduce installation and cable cost
    • Easy detection of disturbances by intelligent DMX protocol supervisor
    • Clean and clear amplification of DMX signals
    • DMX line can be terminated by pressing a button
    • Extend DMX lines infinitely with the splitter
    • Strong Power Supply worldwide 50VAC – 276VAC
    • Input (universes) 1pcs, DMX, XLR 5 pin or XLR 3 pin
    • Through (universes) 1pcs, DMX, XLR 5 pin or XLR 3 pin
    • Outputs 5pcs, DMX, XLR 5 pin or XLR 3 pin
    • Box version, M10 thread for a clamp and a eye bolt for safety line
    • 2 year warrranty
    Quick Links: SKU# XSP-SERIES-SPLITTER
    Details

  • Swisson DMX Opto-Splitter 5 Pin XLR In & Thru – 3 Pin XLR Out

    SKU# XSP-OPTO-SPLITTER
    The Swisson DMX Opto-Splitter 5 Pin XLR In & Thru - 3 Pin XLR Out, perfect for a user looking to connect another DMX input, without wasting an additional output on the splitter. SWISSON-XSP-5B5-US: The DMX Opto-Splitter 5 Pin XLR In & Thru - 3 Pin XLR Out Box is a compact box structure with one 5 Pin XLR input, one 5 Pin XLR through, and five 3 Pin XLR outputs SWISSON-XSP-5R5-US: The DMX Opto-Splitter 5 Pin XLR In & Thru - 3 Pin XLR Out Single Rack is a rack mountable Opto-Splitter equipped with flanges on both ends, one 5 Pin XLR input, one 5 Pin XLR through, and five 3 Pin XLR outputs SWISSON:XSP-5R5-5R5-US: The DMX Opto-Splitter 5 Pin XLR In & Thru - 3 Pin XLR Out Double Rack is capable of being mounted with the included flanges, equipped with two 5 Pin XLR inputs, two 5 Pin XLR through ports, and ten 3 Pin XLR outputs
    • ETL/cETL/CE certified
    • Optical isolation prevents signal disturbances
    • Isolation between input and outputs as well as full isolation between each output
    • Simplify connections and reduce installation and cable cost
    • Easy detection of disturbances by intelligent DMX protocol supervisor
    • Clean and clear amplification of DMX signals
    • DMX line can be terminated by pressing a button
    • Extend DMX lines infinitely with the splitter
    • Strong Power Supply worldwide 5VAC - 276VAC
    • Input (1 universe) 1pcs
    • Through (1 universe) 1pcs
    • Outputs 5 pcs
    • Box version, M10 thread for a clamp and an eye bolt for safety line
    • Dimensions Rack: 19", 1 Unit, 111 mm, Box: 220x111x44mm
    • 2 Year warranty
    Quick Links: SKU# XSP-OPTO-SPLITTER
    Details
  • Swisson DMX Opto-Splitter Switch

    Swisson DMX Opto-Splitter Switch and Mix- Double Rack Mix

    SKU# XSP-OPTO-SPLITTER-MIX
    DMX splitters are the backbone of any DMX512 installation. The XSP series of splitters offer the highest level of reliability for professional use for events or on installations. The specially designed power supply ensures safe operation even under harsh mains conditions. Each port is optically isolated and very well protected against transient over voltages. Swisson-XSP-5R2-5R2-US The DMX Opto-Splitter 5 Pin XLR In & Thru – three 5 Pin and two 3 Pin XLR Out Double Rack is capable of being mounted with the included flanges, equipped with two 5 Pin XLR inputs, two 5 Pin XLR through ports, six 5 Pin XLR outputs and four 3 Pin XLR outputs. Swisson-XSP-5R-5R5-US The DMX Opto-Splitter 5 Pin XLR In & Thru – five 5 Pin and five 3 Pin XLR Out Double Rack is capable of being mounted with the included flanges, equipped with two 5 Pin XLR inputs, two 5 Pin XLR through ports, five 5 Pin XLR outputs and five 3 Pin XLR outputs. Swisson-XSP-5R-3R-US The DMX Opto-Splitter 5 and 3 Pin XLR In & Thru – five 5 Pin and five 3 Pin XLR Out Double Rack is capable of being mounted with the included flanges, equipped with one 5 Pin and one 3 Pin XLR input, one 5 Pin and one 3 Pin XLR through port, five 5 Pin XLR outputs and five 3 Pin XLR outputs. Features
    • ETL/cETL/CE certified
    • Optical isolation prevents signal disturbances
    • Isolation between input and outputs as well as full isolation between each output
    • Simplify connections and reduce installation and cable cost
    • Easy detection of disturbances by intelligent DMX protocol supervisor
    • Clean and clear amplification of DMX signals
    • DMX line can be terminated by pressing a button
    • Extend DMX lines infinitely with the splitter
    • Strong Power Supply worldwide 5VAC – 276VAC
    • Input (1 universe) 1pcs
    • Through (1 universe) 1pcs
    • Outputs 5 pcs
    • Box version, M10 thread for a clamp and an eye bolt for safety line
    • Dimensions Rack: 19″, 1 Unit, 111 mm, Box: 220x111x44mm
    • 2 Year warranty
    Quick Links: SKU# XSP-OPTO-SPLITTER-MIX
    Details

  • Swisson DMX Opto-Splitter Switch and Mix- Single Rack

    SKU# XSP-5R2-US
    DMX splitters are the backbone of any DMX512 installation. The XSP series of splitters offer the highest level of reliability for professional use for events or on installations. The specially designed power supply ensures safe operation even under harsh mains conditions. Each port is optically isolated and very well protected against transient over voltages. Swisson-XSP-5R2-US The DMX Opto-Splitter 5 Pin XLR In & Thru – 3- 5 Pin and 2- 3 Pin XLR Out Single Rack is a rack mountable Opto-Splitter equipped with flanges on both ends, one 5 Pin XLR input, one 5 Pin XLR through, three 5 Pin XLR outputs and two 3 Pin XLR outputs. Features
    • ETL/cETL/CE certified
    • Optical isolation prevents signal disturbances
    • Isolation between input and outputs as well as full isolation between each output
    • Simplify connections and reduce installation and cable cost
    • Easy detection of disturbances by intelligent DMX protocol supervisor
    • Clean and clear amplification of DMX signals
    • DMX line can be terminated by pressing a button
    • Extend DMX lines infinitely with the splitter
    • Strong Power Supply worldwide 5VAC – 276VAC
    • Input (1 universe) 1pcs
    • Through (1 universe) 1pcs
    • Outputs 5 pcs
    • Box version, M10 thread for a clamp and an eye bolt for safety line
    • Dimensions Rack: 19″, 1 Unit, 111 mm, Box: 220x111x44mm
    • 2 Year warranty
    Quick Links:  SKU# XSP-5R2-US
    Details

  • Swisson DMX Opto-Splitter with Terminal Connections

    SKU# XSP-OPTO-SPLITTER-5
    The DMX Opto-Splitter Terminal is equipped with seven terminal ports which allow the user to directly hardwire into a DMX device for permanent fixtures. With the terminal connectors, the user will save money by not having to purchase additional standard connectors. The DMX Opto-Splitter Terminals make it possible to connect directly into the hardware. SWISSON-XSP-5B5-W-US: The DMX Splitter Terminal Box with Wall Mount comes in a compact box configuration with a wall mount and is equipped with 1 input terminal, 1 through terminal, and 5 output terminals. SWISSON-TR5-US: The DMX Splitter Terminal Single Rack has 1 input terminal, 1 through terminal, 5 output terminals and includes mounting flanges for a rack. SWISSON-XSP-TR5-TR5-US: The DMX Splitter Terminal Double has 2 input terminals, 2 through terminals, 10 output terminals and is rack mountable with the included flanges. The DMX Splitter Terminal Double Rack is essentially two single racks side by side.
    • ETL/cETL/CE certified
    • Optical isolation prevents signal disturbances
    • Isolation between input and outputs as well as full isolation between each output
    • Simplify connections and reduce installation and cable cost
    • Easy detection of disturbances by intelligent DMX protocol supervisor
    • Clean and clear amplification of DMX signals
    • DMX line can be terminated by pressing a button
    • Extend DMX lines infinitely with the splitter
    • Strong Power Supply worldwide 5VAC - 276VAC
    • Input (1 universe) 1pcs
    • Through (1 universe) 1pcs
    • Outputs 5 pcs
    • Box version, M10 thread for a clamp and an eye bolt for safety line
    • Dimensions Rack: 19", 1 Unit, 111 mm, Box: 220x111x44mm
    • 2 Year warranty
      Quick Links: SKU# XSP-OPTO-SPLITTER-5
    Details

  • Swisson DMX Wireless Opto-Splitter

    SKU# XSW-TR-SERIES
    2 Year Warranty The XSW combines CRMX wireless DMX technology with our entire line of DMX splitters. The XSW can operate as a DMX transmitter or as a DMX receiver at the press of a button. The DMX splitter functionality is always available regardless of whether the device is configured as a transmitter or receiver. If only the splitter function is used, the wireless part is switched off. The splitter offers one input port, a thru port and 4 individually optically isolated output ports. Multiple radio links can be operated at the same time, allowing a setup with multiple DMX Universes. Multiple receivers can be connected to a single transmitter. A variety of wireless configurations can be built up with the same XSW components.
    • XSW-TR-CRMX-3B: 3-Pin XLR CRMX Transceiver Box
    • XSW-TR-CRMX-3R: 3-Pin XLR CRMX Transceiver Single Rack
    • XSW-TR-CRMX-5B: 5-Pin XLR CRMX Transceiver Box
    • XSW-TR-CRMX-5R: 5-Pin XLR CRMX Transceiver Single Rack
    • XSW-TR-W-DMX-3B: 3-Pin XLR W-DMX Transceiver Box
    • XSW-TR-W-DMX-3R: 3-Pin XLR W-DMX Transceiver Single Rack
    • XSW-TR-W-DMX-5B: 5-Pin XLR W-DMX Transceiver Box
    • XSW-TR-W-DMX-5R: 5-Pin XLR W-DMX Transceiver Single Rack
    SKU# XSW-TR-SERIES
    Details

  • Swisson Nylon Case for Box Size

    SKU# XAC-CASE-BOX
    Nylon case for Swisson Box size products. SKU# XAC-CASE-BOX
    Details
  • Swisson RDM & DMX A/B Splitter

    Swisson RDM & DMX A/B Splitter

    SKU# XPD-DMX-AB-SPLITTER
    XPD-28 splitters boost, refresh and distribute the DMX signals of two inputs onto eight outputs. This allows for safely going beyond the 32 devices limit of the DMX standard, as well as for building star topologies. Moreover, the XPD-28 can be used as a repeater in order to transport a DMX signal across larger distances just as well. XPD-28-5R-US 2:8, rack mountable DMX and RDM splitter, 5- pin XLR XPD-28-3R-US 2:8, rack mountable DMX and RDM splitter, 3- pin XLR XPD-28-8R-US 2:8, rack mountable DMX and RDM splitter, RJ45 Features
    • OLED display.
    • Metal button/ potentiometer
    • Amplifies/ boosts DMX
    • Splits and cleans DMX signal
    • RDM Protocol
    • Enhanced DMX data regeneration
    • Individual optical isolation on all ports
    • Realtime DMX monitoring
    • DMX Framerate display
    • DMX channel overview
    • 19" Rack mountable
      Quick Links: SKU# XPD-DMX-AB-SPLITTER
    Details
  • Swisson Equipment Success

    Swisson RDM & DMX A/B Splitter Mix

    SKU# XPD-DMX-AB-SPLITTER-MIX
    XPD-28 splitters boost, refresh and distribute the DMX signals of two inputs onto eight outputs. This allows for safely going beyond the 32 devices limit of the DMX standard, as well as for building star topologies. Moreover, the XPD-28 can be used as a repeater in order to transport a DMX signal across larger distances just as well. XPD-28-5R8-US 2:8, rack mountable DMX and RDM splitter, inputs: 5-pin XLR, outputs: 3-pin XLR XPD-28-5R2-US 2:8, rack mountable DMX and RDM splitter, inputs 5-pin XLR, outputs: 6 x 5-pin XLR and 2 x 3-pin XLR XPD-28-5R4-US 2:8, rack mountable DMX and RDM splitter, inputs: 5-pin XLR, outputs: 4 x 5-pin XLR and 4 x 3-pin XLR XPD-28-5R6-US 2:8, rack mountable DMX and RDM splitter, inputs 5-pin XLR, outputs: 2 x 5-pin XLR and 6 x 3-pin XLR Features
    • OLED display.
    • Metal button/ potentiometer
    • Amplifies/ boosts DMX
    • Splits and cleans DMX signal
    • RDM Protocol
    • Enhanced DMX data regeneration
    • Individual optical isolation on all ports
    • Realtime DMX monitoring
    • DMX Framerate display
    • DMX channel overview
    • 19″ Rack mountable
    Quick Links: SKU# XPD-DMX-AB-SPLITTER-MIX
    Details

  • Swisson RDM & DMX Opto-Splitter

    SKU# XSR-RDM-OPTO-SPLITTER
    The Swisson XSR line of Opto-Splitters are all highly reliable DMX and RDM splitters and boosters with specially designed power supplies to ensure safe operation, even under harsh conditions. With individually optically isolated ports, these splitters are less susceptible to voltage spikes. These RDM & DMX Opto-Splitters boost, regenerate, and distribute both DMX & RDM signals. The Swisson XSR Opto-Splitters are perfect for projects that require demanding DMX performance. SWISSON-XSR-3B-US: RDM & DMX Opto-Splitter Box containing one 3 Pin XLR input, one 3 Pin XLR through, and five 3 Pin XLR outputs. SWISSON-XSR-3R-US: RDM & DMX Opto-Splitter Single Rack equipped with flanges for mounting, one 3 Pin XLR input, one 3 Pin XLR through, and five 3 Pin XLR outputs. SWISSON-XSR-3R-3R-US: RDM & DMX Opto-Splitter Double rack includes mounting flanges, two 3 Pin XLR inputs, two 3 Pin XLR through ports, and ten 3 Pin XLR outputs. SWISSON-XSR-5B-US: RDM & DMX Opto-Splitter Box containing one 5 Pin XLR input, one 5 Pin XLR through, and five 5 Pin XLR outputs. SWISSON-XSR-5R-US: RDM & DMX Opto-Splitter Single Rack equipped with flanges for mounting, one 5 Pin XLR input, one 5 Pin XLR through, and five 5 Pin XLR outputs. SWISSON-XSR-5R-5R-US: RDM & DMX Opto-Splitter Double rack includes mounting flanges, two 3 Pin XLR inputs, two 3 Pin XLR through ports, and ten 3 Pin XLR outputs.
    • R Switch to toggle between RDM&DMX compatibility or DMX only mode
    • LED Display
    • ETL/cETL/CE certified
    • Optical isolation prevents signal disturbances
    • Isolation between input and outputs as well as full isolation between each output
    • Simplify connections and reduce installation and cable cost
    • Easy detection of disturbances by intelligent DMX protocol supervisor
    • Clean and clear amplification of DMX signals
    • DMX line can be terminated by pressing a button
    • Extend DMX lines infinitely with the splitter
    • Strong Power Supply worldwide 5VAC - 276VAC
    • Input (1 universe) 1pcs
    • Through (1 universe) 1pcs
    • Outputs 5 pcs
    • Box version, M10 thread for a clamp and an eye bolt for safety line
    • Dimensions Rack: 19", 1 Unit, 111 mm, Box: 220x111x44mm
    • 2 Year warranty
    Quick Links: SKU# XSR-RDM-OPTO-SPLITTER
    Details
  • Swisson Equipment Success

    Swisson RDM & DMX Opto-Splitter Switch and Mix

    SKU# XSR-OPTO-SPLITTER-MIX
    The Swisson XSR line of Opto-Splitters are all highly reliable DMX and RDM splitters and boosters with specially designed power supplies to ensure safe operation, even under harsh conditions. With individually optically isolated ports, these splitters are less susceptible to voltage spikes. These RDM & DMX Opto-Splitters boost, regenerate, and distribute both DMX & RDM signals. The Swisson XSR Opto-Splitters are perfect for projects that require demanding DMX performance. XSR-5R2-5R2-US The RDM & DMX Opto-Splitter 5 Pin XLR In & Thru – three 5 Pin and two 3 Pin XLR Out Double Rack is capable of being mounted with the included flanges, equipped with two 5 Pin XLR inputs, two 5 Pin XLR through ports, six 5 Pin XLR outputs and four 3 Pin XLR outputs. XSR-5R-5R5-US The RDM & DMX Opto-Splitter 5 Pin XLR In & Thru – five 5 Pin and five 3 Pin XLR Out Double Rack is capable of being mounted with the included flanges, equipped with two 5 Pin XLR inputs, two 5 Pin XLR through ports, five 5 Pin XLR outputs and five 3 Pin XLR outputs. XSR-5R-3R-US The RDM & DMX Opto-Splitter 5 and 3 Pin XLR In & Thru – five 5 Pin and five 3 Pin XLR Out Double Rack is capable of being mounted with the included flanges, equipped with one 5 Pin and one 3 Pin XLR input, one 5 Pin and one 3 Pin XLR through port, five 5 Pin XLR outputs and five 3 Pin XLR outputs. Features
    • R Switch to toggle between RDM&DMX compatibility or DMX only mode
    • LED Display
    • ETL/cETL/CE certified
    • Optical isolation prevents signal disturbances
    • Isolation between input and outputs as well as full isolation between each output
    • Simplify connections and reduce installation and cable cost
    • Easy detection of disturbances by intelligent DMX protocol supervisor
    • Clean and clear amplification of DMX signals
    • DMX line can be terminated by pressing a button
    • Extend DMX lines infinitely with the splitter
    • Strong Power Supply worldwide 5VAC – 276VAC
    • Input (1 universe) 1pcs
    • Through (1 universe) 1pcs
    • Outputs 5 pcs
    • Box version, M10 thread for a clamp and an eye bolt for safety line
    • Dimensions Rack: 19″, 1 Unit, 111 mm, Box: 220x111x44mm
    • 2 Year warranty
    Quick Links: SKU# XSR-OPTO-SPLITTER-MIX
    Details

  • Swisson RDM & DMX Opto-Splitter Switch and Mix- Single

    SKU# XSR-5R2-US
    The Swisson XSR line of Opto-Splitters are all highly reliable DMX and RDM splitters and boosters with specially designed power supplies to ensure safe operation, even under harsh conditions. With individually optically isolated ports, these splitters are less susceptible to voltage spikes. These RDM & DMX Opto-Splitters boost, regenerate, and distribute both DMX & RDM signals. The Swisson XSR Opto-Splitters are perfect for projects that require demanding DMX performance. Swisson XSR-5R2-US The RDM & DMX Opto-Splitter 5 Pin XLR In & Thru – 3-5 Pin and 2-3 Pin Out XLR Single Rack includes hardware for mounting onto racks, one 5 Pin XLR input, one 5 Pin XLR through, three 5 Pin XLR outputs and two 3 Pin XLR outputs. Features
    • R Switch to toggle between RDM&DMX compatibility or DMX only mode
    • LED Display
    • ETL/cETL/CE certified
    • Optical isolation prevents signal disturbances
    • Isolation between input and outputs as well as full isolation between each output
    • Simplify connections and reduce installation and cable cost
    • Easy detection of disturbances by intelligent DMX protocol supervisor
    • Clean and clear amplification of DMX signals
    • DMX line can be terminated by pressing a button
    • Extend DMX lines infinitely with the splitter
    • Strong Power Supply worldwide 5VAC – 276VAC
    • Input (1 universe) 1pcs
    • Through (1 universe) 1pcs
    • Outputs 5 pcs
    • Box version, M10 thread for a clamp and an eye bolt for safety line
    • Dimensions Rack: 19″, 1 Unit, 111 mm, Box: 220x111x44mm
    • 2 Year warranty
    Quick Links:  SKU# XSR-5R2-US
    Details

  • Swisson RDM & DMX Opto-Splitter w/ Terminal

    SKU# XSR-OPTO-SPLITTER-TERMINAL
    The RDM & DMX Opto-Splitter is a convenient, less expensive way to build a permanent fixture. The terminal ports allow the user to directly connect into the hardwire of a device, instead of spending extra money on other connecters. SWISSON-XSR-IB5-W-US: The RDM & DMX Opto-Splitter Terminal Box with Wall Mount is a compact structure with 1 input terminal, 1 through terminal, and 5 output terminals. SWISSON-XSR-TR5-US: The RDM & DMX Opto-Splitter Terminal Single Rack includes built in flanges for mounting, 1 input terminal, 1 through terminal, and 5 output terminals. SWISSON-XSR-TR5-TR5-US: The RDM & DMX Opto-Splitter Terminal Double Rack is equipped with flanges for easy rack mounting, 2 input terminals, 2 through terminals, and 10 output terminals.
    • R Switch to toggle between RDM&DMX compatibility or DMX only mode
    • LED Display
    • ETL/cETL/CE certified
    • Optical isolation prevents signal disturbances
    • Isolation between input and outputs as well as full isolation between each output
    • Simplify connections and reduce installation and cable cost
    • Easy detection of disturbances by intelligent DMX protocol supervisor
    • Clean and clear amplification of DMX signals
    • DMX line can be terminated by pressing a button
    • Extend DMX lines infinitely with the splitter
    • Strong Power Supply worldwide 5VAC - 276VAC
    • Input (1 universe) 1pcs
    • Through (1 universe) 1pcs
    • Outputs 5 pcs
    • Box version, M10 thread for a clamp and an eye bolt for safety line
    • Dimensions Rack: 19", 1 Unit, 111 mm, Box: 220x111x44mm
    • 2 Year warranty
    Quick Links: SKU# XSR-OPTO-SPLITTER-TERMINAL
    Details

  • Swisson RDM & DMX Opto-Splitter XLR 5 In & Thru

    SKU# XSR-RDM-OPTO-SPLITTER-5
    SWISSON-XSR-5B5-US: The RDM & DMX Opto-Splitter 5 Pin XLR In & Thru - 3 Pin Out XLR Box is ideal for limited space and is equipped with one 5 Pin XLR input, one 5 Pin XLR through, and five 3 Pin XLR outputs. SWISSON-XSR-5R5-US: The RDM & DMX Opto-Splitter 5 Pin XLR In & Thru - 3 Pin Out XLR Single Rack includes hardware for mounting onto racks, one 5 Pin XLR input, one 5 Pin XLR through, and five 3 Pin XLR outputs. SWISSON-XSR-5R5-5R5-US: The RDM & DMX Opto-Splitter 5 Pin XLR In & Thru - 3 Pin Out XLR Double Rack includes flanges for easy mounting, two 5 Pin XLR inputs, two 5 Pin XLR through ports, and ten 3 Pin XLR outputs.
    • R Switch to toggle between RDM&DMX compatibility or DMX only mode
    • LED Display
    • ETL/cETL/CE certified
    • Optical isolation prevents signal disturbances
    • Isolation between input and outputs as well as full isolation between each output
    • Simplify connections and reduce installation and cable cost
    • Easy detection of disturbances by intelligent DMX protocol supervisor
    • Clean and clear amplification of DMX signals
    • DMX line can be terminated by pressing a button
    • Extend DMX lines infinitely with the splitter
    • Strong Power Supply worldwide 5VAC - 276VAC
    • Input (1 universe) 1pcs
    • Through (1 universe) 1pcs
    • Outputs 5 pcs
    • Box version, M10 thread for a clamp and an eye bolt for safety line
    • Dimensions Rack: 19", 1 Unit, 111 mm, Box: 220x111x44mm
    • 2 Year warranty
    Quick Links: SKU# XSR-RDM-OPTO-SPLITTER-5
    Details

  • Swisson RJ45 RDM & DMX Opto-Splitter

    SKU# RJ45-OPTO-SPLITTER
    The Swisson RJ45 RDM/DMX Splitter XSR-8B, Swisson RJ45 RDM/DMX Splitter XSR-8R-8R, and the Swisson RJ45 RDM/DMX Splitter XSR-8R are top of the line DMX/RDM splitters and boosters that processes DMX and RDM signals with a high level of reliability for professional applications.
    • ETL/cETL/CE certified
    • Switch for RDM & DMX or DMX only
    • LED display; signal, power, RDM
    • Optical isolation prevents signal disturbances
    • Isolation between input and outputs as well as full isolation between each output
    • Simplify connections and reduce installation and cable cost
    • Easy detection of disturbances by intelligent DMX and RDM protocol supervisor
    • Clean and clear amplification of DMX and RDM signals
    • DMX line can be terminated by pressing a button
    • Extend DMX lines infinitely with the splitter
    XSR-8B-US: The RJ45 RDM & DMX Opto-Splitter Box is ETL/cETL/CE certified, equipped with one RJ45 input, one RJ45 through, five RJ45 outputs and a NEMA 5-15 molded plug. XSR-8R-US: The RJ45 RDM& DMX Single Rack is an ETL/cETL/CE certified, easily mountable rack with one RJ45 input, one RJ45 through, five RJ45 outputs and a NEMA 5-15 molded plug. XSR-8R-8R-US: The RJ45 RDM& DMX Double Rack is an ETL/cETL/CE certified, easily mountable rack with two RJ45 input, two RJ45 through, ten RJ45 outputs and a NEMA 5-15 molded plug. Quick Links: SKU# RJ45-OPTO-SPLITTER
    Details

  • Swisson Wireless DMX Transmitters & Receivers

    SKU# SWISSON-XWL-TR
    • XWL-T-CRMX-3: 3-Pin XLR CRMX Wireless DMX Transmitter
    • XWL-T-CRMX-5: 5-Pin XLR CRMX Wireless DMX Transmitter
    • XWL-R-CRMX-3: 3-Pin XLR CRMX Wireless DMX Receiver
    • XWL-R-CRMX-5: 5-Pin XLR CRMX Wireless DMX Receiver
    • XWL-T-W-DMX-3: 3-Pin XLR W-DMX Wireless DMX Transmitter
    • XWL-T-W-DMX-5: 5-Pin XLR W-DMX Wireless DMX Transmitter
    • XWL-R-W-DMX-3: 3-Pin XLR W-DMX Wireless DMX Receiver
    • XWL-R-W-DMX-5: 5-Pin XLR W-DMX Wireless DMX Receiver
    The XWL series encompasses both, W-DMX as well as CRMXcompatible and compact wireless DMX transmitters and receivers. W-DMX from Wireless Solution and CRMX from LumenRadio are the leading technologies for wireless DMX transmission. With a latency of only about 5 ms, CRMX and W-DMX guarantee a DMX connection with the properties and reliability level equivalent to those of a wired link.

    Several transmitters can be operated in parallel, each of which is easily linkable to any number of receivers and capable of handling one full universe of 512 DMX channels.

    All XWL products are equipped with M10/M12 and 3/8" threads to provide a variety of installation possibilities, such as mounting on a microphone stand.

    • Wireless DMX receiver (XWL-R models)
    • Wireless DMX transmitter (XWL-T models)
    • Available with W-DMX™ or CRMX™
    • M10/M12 threads for truss mount
    • 3/8” thread for mounting on a microphone stand
    • Built-in power supply (powerCON connected)
    • Compact, rugged housing
    Quick Links: SKU# SWISSON-XWL-TR
    Details

  • Swisson XAC-ANT-2.4 Antenna 2.4 GHz to XSW

    SKU# XAC-ANT-2.4
    Replacement antenna for Swisson Wireless Opto-Splitter. SKU# XAC-ANT-2.4
    Details

  • Swisson XMG-51 DMX High Speed Merger

    SKU# XMG-51
    The DMX Merger XMG-51 is a 5 input, one merge output, 5 pin XLR system that merges 5 DMX lines together into one. The XMG-51 DMX Merger combines up to five DMX lines together into one. This allows multiple DMX lighting control systems are used simultaneously on a single light installation. The DMX data is merged together according from simple to complex combination that you can configure. The operating modes and rules can be combined. This allows for a variety of possibilities of operation: Multiple lighting controllers can share one of the 512 DMX channels. For example, controller A controls the channels 1-48, controller B controls the channel 50-74 and the channels 200-400 are controlled by controller C. Several light controllers can operate on the same channels. For example, a single Lamp can be controlled by all controllers at the same time. Which controller has priority is configurable (HTP, LTP). A mobile lighting controller could be plugged in different places of the venue. The merger recognizes where the controller is plugged in and switches automatically the corresponding port to the output. A backup lighting controller can be used at the same time as the main lighting controller by using the XMG-51Merger. The merger will automatically switch to the backup controller in the case of a failure of the main controller. It can also be switched manually at any time. The XMG-51 has a built in bypass relay which connects the output with a dedicated input in event of a power supply failure.
    • 5 DMX512 inputs
    • 1 DMX512 output
    • Only 50us latency
    • Bypass relay
    • Manual switch
    • HTP, LTP channel, LTP line Modes
    • Channel offset for each input
    • Connect up to 5 lighting desks into one DMX-512 line
    • Fast uplink port with only 0.00005 second delay
    • Manual access
    • Channel offset for each port
    • Switch mode for backup
    • HTP merge mode (Highest Takes Precedence)
    • LTP merge mode (Last Takes Precedence)
    • HTP or LTP for each channel
    • Overwrite by priority
    • Optical isolated
    • Works on worldwide power supplies, 85V up to 267V
    Quick Links: SKU# XMG-51
    Details
Visit Our YouTube Channel
BBB Accredited Business
C RU US Logo
C UL US Logo
IES Illuminating logo

IMPORTANT LINKS

About Us
Manufacturing & OEM Services
Security
Shipping & Return Policy
Terms of Use
Privacy Policy
Ordering
Careers
Contact Us

CONTACT INFORMATION

SIRS Electronics, Inc.
3307 West Street
Rosenberg, TX 77471


(281) 324-0908
9am – 6pm M-F (CDT)
We Ship World Wide
We also speak Spanish

We take pride in designing LED strips right here in Houston, Texas, USA, and manufacturing a majority of them locally. Our commitment to American production supports the local industry and ensures high-quality products. God Bless America!

Made in USA
SIRS-E Green Solution

Copyright © 2024 SIRS-E® All Rights Reserved – 3307 West Street, Rosenberg, TX 77471
SIRS-E: {semiconductor • illumination • research • solutions}

We use cookies to ensure that we give you the best experience on our website. If you continue to use this site we will assume that you are happy with it. OK
Go to Top