-
SKU# LED-PIXEL-T-PWT Cable for LED Pixels used in daisy chain configuration, allows you to add more power supplies in the chain or a DMX terminator at the end. 3 Connectors
- 4 Pin Waterproof lock connection MALE
- 4 Pin Waterproof lock connection FEMALE
- 2 Pin Waterproof lock connection MALE
-
SKU# LED-PIXEL-T-INI-DMXInitial T Cable for LED Pixels. Use this cable to begin your chain. Add DMX signal, Power and Connect to the vertical tube or pixel cable.
- XLR 3 Pin MALE (DMX IN)
- 4 Pin Waterproof lock connection FEMALE (Power/DMX signal)
- 2 Pin Waterproof lock connection MALE (Power)
-
SKU# LED-PIXEL-12Features:
- Can be seen from 360°
- Full dimming capability 0%-100%
- Full RGB capability
- Works with any type of DMX control
- Colorful and vivid effects can easily be achieved
- If set up in group, great 2D effects can be achieved
- One year warranty
- High quality diffused plastic casing for optimum optics
- Mounting brackets included for installation
- Model: LED-PIXEL-12
- Operating Voltage: DC 24V
- Max Current: 3.6W
- Ambient Temperature: -20°C~60°C
- IP Rating: IP65
- LED Type: SMD RGB 5050
- Total LEDs: 3
- Total Pixels: 1
- Total DMX Channels: 3
- DMX Addressability: Self Address
- Viewing Angle: 360°
- Weight: 264g
- 104mm x 104mm x 83mm
- 4.09in. x 4.09in. x 3.26in
-
Out of stockSKU# DMX-TEST-02Free Ground Shipping.
The simple un-expensive DMX Tester and Terminator will allow users to see if a device is properly sending or receiving a DMX Signal. Also will work as a Terminator and prevents the fast DMX signal from bouncing back down the line and causing flicker and other problems. It is safe to leave this product connected all the time.
How it Works:- Orange/Yellow LED: A orange/yellow LED indicates a good DMX signal.
- Red LED: If you see red only then you have DMX signal problem such as inverse polarity.
- No LED: If the LED is off then you have pin 2 or 3 cut off.
High Quality Material
- Bicolor LED Diode
- Genuine Neutrik XLR Male 3 Pin
- DMX Adapter 3 Pole Female to 5 Pole Male 70029
- 120 ohms, 2 W Resistor Non-Flammable
Warranty: 1 Year
SKU# DMX-TEST-02 -
Out of stockSKU# DMX-TEST-01Free Ground Shipping.
The simple inexpensive DMX Tester and Terminator will allow users to see if a device is properly sending or receiving a DMX Signal. Also, it will work as a Terminator and prevents the fast DMX signal from bouncing back down the line and causing flicker and other problems. It is safe to leave this product connected all the time.
How it Works
- Orange/Yellow LED: A orange/yellow LED indicates a good DMX signal.
- Red LED: if you see red only then you have DMX signal problem such as inverse polarity.
- No LED: If the LED is off then you have pin 2 or 3 cut off.
High Quality Material
- Bicolor LED Diode
- Genuine Neutrik XLR Male 3 Pin
- 120 ohms, 2 W Resistor Non-Flammable
Warranty: 1 Year
SKU# DMX-TEST-01 -
SKU# IA-HW-001001Important Links:
The USB ONE allows you to control 512 DMX channels via Madrix software.
- DMX-IN/OUT with 5-pin NEUTRIK XLR Port: This device allows you to send or receive data via MADRIX using 512 DMX channels. A gender changer with 5-pin male to 3-pin or 5-pin male is required for DMX-IN.
- USB 2.0 Standard: The latest USB 2.0 standard is fully supported to allow for a higher maximum speed of 480Mbit/s.
- Power Over USB: The interface is powered directly via the USB port and does not need an additional power supply.
- Hot Swapping & Plug and Play: Devices can be connected to and disconnected from the computer during use and without a reboot.
- Remote Control: MADRIX can be controlled remotely using the built-in DMX-IN functions.
- Frame Rate Stability: Up to 60 devices can be connected to a single USB host controller without having any frame rate problems (60 DMX512 interfaces amount to 30,720 DMX channels).
- Active USB: Must be connected to an active USB 2.0 hub with a power supply.
-
Out of stockSKU# 70572Quick Links:
ShopMark Eviota2024-04-02T12:17:21-05:00