-
SKU# XLRJ45-XXXLRJ45-3F | RJ45 to 3-Pin XLR Female Adaptor One-piece RJ45 to 3-pin XLR Female Adaptor (Using ESTA standard pinout) XLRJ45-3M | RJ45 to 3-Pin XLR Male Adaptor One-piece RJ45 to 3-pin XLR Male Adaptor (Using ESTA standard pinout) XLRJ45-5F | RJ45 to 5-Pin XLR Female Adaptor One-piece RJ45 to 5-pin XLR Female Adaptor (Using ESTA standard pinout) XLRJ45-5M | RJ45 to 5-Pin XLR Male Adaptor One-piece RJ45 to 5-pin XLR Male Adaptor (Using ESTA standard pinout) Downloadable Documentation: SKU# XLRJ45-XX -
SKU# XLR3-TERM XLR5-TERMDMXterminator XLR is an XLR connector plug with a 120 Ohm resistor inside connected to the data lines. Plug this in at the last DMX unit, and the DMX source perceives the cable as endless. Otherwise, reflections can be caused at the end of the line, creating problems that can be very difficult to find. Avoid this by terminating the end of the cable. FEATURES- A 120 Ohm DMX512 Terminator in an XLR connector
- Two XLR versions available, male 3-pin or male 5-pin
- Plug directly into any 3-pin or 5-pin XLR DMX512-controlled equipment
- Use to avoid data signals being reflected from the end of the data cable
- Very robust, rugged molded housing with non-slip grip
- Product Weight (including packaging): 31g / 1.1oz
- Gold-plated pins on the connector
- Easy to use
- Low cost
- RoHS, REACH, and California Prop65 Certified
-
SKU# RJ45-DMXTERM-120-XXRJ45-DMXTERM-120 or RJ45-DMXTERM-120-2U is an RJ45 connector plug with a 120 Ohm resistor inside connected to the data lines. Plug this in at the last DMX unit, and the DMX source perceives the cable as endless. Otherwise, reflections are created at the end of the cable, causing problems that are very difficult to find. Avoid this by terminating the end of the cable. is an RJ45 connector plug with a 120 Ohm resistor inside connected to the data lines. Plug this in at the last DMX unit, and the DMX source perceives the cable as endless. Otherwise, reflections are created at the end of the cable, causing problems that are very difficult to find. Avoid this by terminating the end of the cable. -
SKU# DMXCOMPDMXcompander RJ45 DMX Compander 3 DMX Universes Over 1 CAT5 Cable DMXcompander makes it possible to run three DMX512 Universes in one CAT-5 cable. A CAT-5 cable has four data pairs, one pair is used as the 0V reference and the other three pairs are used for DMX512 Data+ and Data-. Through the three RJ45 connectors on the DMXcompander, three DMX512 Universes are "COMpressed" into one CAT-5 cable through the Universe 1+2+3 RJ45 connector. At the other end of the CAT-5 cable, another DMXcompander can be used to "exPAND" the DMX512 Universes again, making them available through the three RJ45 connectors. Together with CAT-5 cables and CPOINT's XLR RJ45 adapters, a DMX512 network can be set up very quickly and at a very low cost Product Features- Three DMX512 Universes (1536 channels) combined into one CAT-5 cable
- RJ45 connectors are used for connection with inexpensive CAT-5 cables
- Gold-plated pins on RJ45 connectors
- Sturdy molded housing
- Mountable on DIN rail
- Mountable in the lighting rig
- Use as a flexible DMX outlet
- Mountable with 5mm/0.2” screws or cable tie
- Weight including packaging, 49g/1.73oz
- EAN13 Barcode on the packaging
- Lightweight packaging
- Easy to use
- RoHS, REACH, and California Prop65 Certified
-
SKU# DMXTENDERDMXtender A mountable sturdy CAT-5 cable extender DMXtender makes it possible to connect two CAT-5 cables together. The DMXtender can be mounted on a DIN rail, lighting rig, wall, etc. The sturdy design of the DMXtender makes it suitable for professional use. Together with the CPoint XLR-RJ45 adapter, a DMX512 network can be built very quickly and at a very low cost. With the CPoint DMXcompander, you can run 1536 channels in one CAT5 cable. Product Features- Use to connect two CAT-5 cables together to make a cable extension
- Gold-plated pins on RJ45 connectors
- Sturdy molded housing with non-slip grip
- Mountable on a DIN rail, lighting rig, wall, etc.
- Mountable with 5mm/0.2” screws or cable tie
- Weight including packaging, 28.4g/1.00oz
- EAN13 Barcode on the packaging
- Lightweight packaging
- Easy to use
- RoHS, REACH, and California Prop65 Certified
- Wall Mount
- Rail Mount
- Rig Mount
-
SKU# LED-PLUG-2MFLED strip and power supply 2 wire plug. Easy installation with only 2 screws. No soldering, splicing or crimping required. Great for multiple uses including:- Single Color LED Strips
- DMX LED Strip Power
- Power Supplies
- Custom Power Cables
- 38mm x 14mm x 13mm
- External Diameter: 5.5mm
- Internal Diameter: 2.1mm
-
SKU# NEUTRIK-XX-4TECHNICAL DATA Electrical- Number of contacts: 4
- Contact resistance: ≤ 3 m
- Insulation resistance
- initial: > 2 G
- after damp heat test: > 1 G
- Dielectric strength: 1500 V dc
- Rated current: 10 A
- AWG: 1.5 mm²/16 AWG
- Capacitance between contacts: ≤ 7 pF
- Lifetime: >1000 cycles
- Insertion / withdrawal force: ≤ 20 N
- Cable O.D. range: 3.5 mm – 8.0 mm
- Shell: ZnAl4Cu1, gal Ni over Cu plating
- Insert: PA 6.6 30% GR (glass reinforced)
- Contacts: CuZn39Pb3
- Contact surface: gal 2 µm Ag
- Strain-relief clamp: POM
- Antikink bushing: PUR
- Temperature range: -30° C to + 80° C
- Flammability: UL 94HB
- Solderability: complies with IEC 68-2-20
- IEC tentative standard & Switchcraft® & Cannon XLR
-
SKU# NC4FP-1TECHNICAL DATA Electrical- Number of contacts: 3 - 7 (except MP: 3-6)
- Rated voltage: 50 V ac
- Contact resistance: < 5 m
- Insulation resistance - initial: > 2 G
- - after damp heat test: > 1 G
- -IEC 68-2-30)
- Dielectric strength: 1500 V dc
- Rated current:
- 3 pole: 16 I [A], 2.5/14 mm2/AWG, ≤ 4 C
- 4 pole: 10 I [A], 1.5/16 mm2/AWG, ≤ 7 C
- 5 and 6 pole: 7.5 I [A], 1.0/18 mm2/AWG, ≤ 7 C
- 7 pole: 5 I [A], 1.0/18 mm2/AWG, ≤ 9 C
- Lifetime: > 1000 mating cycles
- Insertion / withdrawal force: ≤ 20 N
- Retention method (Female versions only): - standard: latch lock
- "-0" version: retention spring
- Separating force: ≤ 20 N
- Shell: ZnAl4Cu1, gal Ni or black Cr plating
- Insert: PA 6.6 30% GR (glass reinforced)
- Contacts: - female (3 pole): CuSn6
- female (4-7pole) & male: CuZn39Pb3
- Contact surface: gal 2 µm Ag or gal 0.2 µm Au hard alloy over 2 µm Ni
- Latch lock & spring: CK 67 steel, treated
- Temperature range: -30° C to + 80° C
- Flammability: UL 94HB
- Solderability: complies with IEC 68-2-20
-
SKU# NAC3FCBLockable cable connector, power-out, screw terminals, grey The powerCON is a locking 3 conductor equipment AC connector with contacts for line, neutral and pre-mating ground contact. It replaces appliance couplers wherever a very rugged solution in combination with a locking device is needed in order to guarantee a safe power connection. Attention: The powerCON is a connector without breaking capacity, i.e. the powerCON should not be connected or disconnected under load or live! Features & Benefits- Locking 20 A / 250 V ac appliance coupler
- 3 contacts for line, neutral and premating safety ground
- Power-in (blue) and power-out (grey) versions with different keying to avoid the possibility of intermating
- Fast and easy twist lock latching system
- Extremely robust and reliable
- Ergonomic design
- User friendly latch design for easy handling
- Unique Neutrik chuck type strain relief
- UL, cUL recognized components
- VDE certified
- SEV approved
- Branded with unique hologram - guarantees genuine and authentic Neutrik product
Note: Item comes disassembled SKU# NAC3FCB -
SKU# NAC3MPBChassis connector, power-out, 3/16'' flat tab terminals, grey The powerCON is a locking 3 conductor equipment AC connector with contacts for line, neutral and pre-mating ground contact. It replaces appliance couplers wherever a very rugged solution in combination with a locking device is needed in order to guarantee a safe power connection. Attention: The powerCON is a connector without breaking capacity, i.e. the powerCON should not be connected or disconnected under load or live! Features & Benefits- Locking 20 A / 250 V ac appliance coupler
- 3 contacts for line, neutral and premating safety ground
- Power-in (blue) and power-out (grey) versions with different keying to avoid the possibility of intermating
- Fast and easy twist lock latching system
- Extremely robust and reliable
- Ergonomic design
- User friendly latch design for easy handling
- UL, cUL recognized components VDE certified SEV approved
- Branded with unique hologram - guarantees genuine and authentic Neutrik product
-
SKU# NAC3MPAChassis connector, power-in, 3/16'' flat tab terminals, blue The powerCON is a locking 3 conductor equipment AC connector with contacts for line, neutral and pre-mating ground contact. It replaces appliance couplers wherever a very rugged solution in combination with a locking device is needed in order to guarantee a safe power connection. Attention: The powerCON is a connector without breaking capacity, i.e. the powerCON should not be connected or disconnected under load or live! Features & Benefits- Locking 20 A / 250 V ac appliance coupler
- 3 contacts for line, neutral and premating safety ground
- Power-in (blue) and power-out (grey) versions with different keying to avoid the possibility of intermating
- Fast and easy twist lock latching system
- Extremely robust and reliable
- Ergonomic design
- User friendly latch design for easy handling
- UL, cUL recognized components
- VDE certified
- SEV approved
- Branded with unique hologram - guarantees genuine and authentic Neutrik product
-
SKU# NAC3FCALockable cable connector, power-in, screw terminals, blue The powerCON is a locking 3 conductor equipment AC connector with contacts for line, neutral and pre-mating ground contact. It replaces appliance couplers wherever a very rugged solution in combination with a locking device is needed in order to guarantee a safe power connection. Attention: The powerCON is a connector without breaking capacity, i.e. the powerCON should not be connected or disconnected under load or live! Features & Benefits- Locking 20 A / 250 V ac appliance coupler
- 3 contacts for line, neutral and premating safety ground
- Power-in (blue) and power-out (grey) versions with different keying to avoid the possibility of intermating
- Fast and easy twist lock latching system
- Extremely robust and reliable
- Ergonomic design
- User friendly latch design for easy handling
- Unique Neutrik chuck type strain relief
- UL, cUL recognized components
- VDE certified
- SEV approved
- Branded with unique hologram - guarantees genuine and authentic Neutrik product
Note: Item comes disassembled
Quick Links:
SKU# NAC3FCA
Main 281-324-0908 | 9AM - 6PM M-F (CDT)
SUBSCRIBE TO OUR NEWSLETTER
We take pride in designing LED strips right here in Houston, Texas, USA, and manufacturing a majority of them locally. Our commitment to American production supports the local industry and ensures high-quality products. God Bless America!
